Installation Instructions Original Instructions POINT I/O Protected Output Module Catalog Numbers 1734-OB2E, 1734-OB4E, 1734-OB8E, 1734-OB8EK, Series C Catalog numbers with the suffix ‘K’ are conformal coated and their specifications are the same as non-conformal coated catalogs. Topic Page Summary of Changes 1 Before You Begin 5 Install the Mounting Base 5 Install the Module 5 …
The 1734-OB8E is a protected discrete input module that is part of Allen-Bradley’s POINT IO product family. This module features Eight (8) 1 group of 8, non-isolated, sourcing, output channels. Each channel has an operating voltage range of 10-28.8 VDC with maximum output current rating of 1 A per output and 2 A per module. This module has maximum Surge current of 2 A with built-in electronic protection.
Installation Instructions POINT I/O Dual Port EtherNet/IP Adapter Catalog numbers 1734-AENTR Table of Contents Topic Page Important User Information 2 Environment and Enclosure 3 Preventing Electrostatic Discharge 3 North American Hazardous Location Approval 4 European Hazardous Location Approval 4 About The Adapter 6 Before You Begin 7 Determine Compatibility 7 Understand Messaging 7 Configure Autobaud …
The Allen-Bradley 1734-AENTR is a Point I/O Dual Ethernet communication module. It supports Ring, Star, and Tree Topology and transmission speed of 10/100 Mbits/s in Half or Full-Duplex mode. This module supports DIN rail mounting and requires 24 Volts DC Input Voltage.
https://www.plc-hub.com/installation-guide-of-1734-aentr/
Installation Instructions POINT I/O EtherNet/IP Adapter Catalog numbers 1734-AENT Table of Contents Topic Page Important User Information 2 Environment and Enclosure 3 Preventing Electrostatic Discharge 3 North American Hazardous Location Approval 4 European Hazardous Location Approval 4 About The Adapter 6 Before You Begin 7 Firmware Backward Compatibility 7 Understand Messaging 7 Configure Autobaud 7 …
The Allen-Bradley 1734-AENT is a POINT I/O Ethernet I/P communication adapter. This module provides Ethernet connectivity for sending and receiving POINT I/O module information to the master controller. This module has One (1) Ethernet interface, supporting 10/100 Mbits/s, half or full-duplex transmission rate supporting Linear, Star and Tree topology. It is powered by a 24 VDC supply Voltage and mounted to a DIN Rail.
Install Guide of 1734-AENT:
https://www.plc-hub.com/installation-guide-of-1734-in590/
The Allen-Bradley 1734-OB8S is a POINT I/O Safety I/O Module. It has Eight (8) Current Sourcing Output channels and operates with Supply Voltage of 24 Volts DC. This Safety I/O Module is used with GuardLogix and SmartGuard controllers.
Install Instruction:
https://www.plc-hub.com/installation-instructions1734-in016/
User Manual
https://www.plc-hub.com/point-guard-i-o-safety-modules-user-manual/
Installation Instructions Original Instructions POINT Guard I/OSafety Modules Catalog Numbers 1734-IB8S, 1734-IB8SK, 1734-OB8S, 1734-OB8SK, 1734-IE4S, 1734-IE4SK, 1734-OBV2S, 1734-OBV2SK ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or maintain this product. Users are required to familiarize themselves with …
1734-IB8S is a POINT I/O Guard I/O Safety Module. It has Eight (8) Current Sinking Safety Input channels and Four (4) Current Sourcing Pulse Test Outputs. It requires a nominal supply voltage of 24VDC.
https://www.plc-hub.com/?p=5862&preview=true
https://www.plc-hub.com/point-guard-i-o-safety-modules-user-manual/
The Allen-Bradley 1734-IE2V is a POINT I/O Analog Input Module. It has 2 single-ended, non-isolated, voltage Inputs and a Delta Sigma Conversion Type with a Power Dissipation of 0.75 Watts at 28.8 Volts DC. This Analog Input Module has an Open Enclosure Type Rating.