1734-AENT Technical specifications
Manufacturer | Rockwell Automation |
---|---|
Inrush Current | 6 Amps |
Module Type | Ethernet Adapter Module |
Part Number/Catalog No. | 1734-AENT |
Brand | Allen-Bradley |
Product Family: | 1734 POINT I/O |
Product Type: | Communications |
No. of Ports | 1 |
I/O Module Capacity | 63 modules |
I/O Points, max. | 504 |
Communication Rate | 10/100 Mbits/s, half or full-duplex. |
Supported Topologies | Star / Tree topologies |
Indicators | 3 red/green status indicators (on CPU): – Module status – Network status – POINTBus status 1 green status indicator on CPU: – Network activity 2 green power supply status indicators on DC-DC Converter: – System power (5V DC to POINTBus Out) – Field power (24V DC from Field In) |
Topologies: | Star, Tree |
Field Side Power | 400 milliamps |
Power Consumption | 10.4 W @ 28.8V DC |
POINTBus Current | 1000 milliamps |
Power Dissipation | 5.2 Watts (at 28.8 Volts) |
Series | POINT I/O |
Input Voltage Rating | 24 Volts DC |
Dimensions | 30 x 2.16 x 5.25 inches |
Enclosure Type | Open |
Ethernet Connector | RJ-45, Category 5 |
Wire Size | 3/64 inches insulation max |
Chassis Size | 4 |
Input Overvoltage Protection | Reverse Polarity Protected |
Isolation Voltage | 50 Volts (Continuous) |
Maximum Expansion I/O Capacity | 63 Modules, 31 Direct Connections |
Mounting | DIN rail |
UPC | 10612598290434 |
Description
The Allen-Bradley 1734-AENT is a POINT I/O Ethernet I/P communication adapter. This module is part of the bulleting 1734 POINT I/O Product family, enabling a POINT I/O rack to exchange real-time I/O data to the master controller in the Ethernet I/P network. It interfaces POINT I/O modules and facilitates transfer not only I/O but diagnostic information as well.
The 1734-AENT has a built-in Ethernet communication port, with RJ45 physical interface. This port supports transmission speed of 10/100 Mbps in half or full-duplex operation. It comes with auto-negotiation capability, eliminating the need to specifically set the transmission rate of the module. The 1734-AENT connects the POINT I/O rack in star and tree topology. It uses Category 5 cable, Shielded or unshielded wires, installed with RJ45 connector on both ends of the cable. The 1734-AENT is provided with LED status indicators used for monitoring the operation of the module and diagnosing in the event of module fault. These indicators include Three (3) red/green status indicators located on the CPU to indicate Module, Network and POINTBus status.
The 1734-AENT is supplied with 24V DC voltage to energize the module with field bus power supply current of 10 A. The acceptable supply range of the 1734-AENT is 10-28.8VDC. The 1734-AENT has an integral Reverse Polarity Protection.
The 1734-AENT may be installed up to 63 POINT I/O modules or maximum of 504 input and output points. Expansion power supplies may be installed to provide sufficient POINTBus current to the modules installed in the POINT I/O rack. One (1) expansion power supply may supply power to a maximum of 17 modules.
This module can communicate with other POINT I/O modules on the same DIN rail. The IP addresses in this module are assigned via the standard BootP or DHCP tools. The Allen-Bradley 1734-AENT can support connections from several controllers simultaneously. The 1734-AENT adapter has 24 Volts DC input voltage rating and an inrush current of 6 A, maximum with dimensions of 30x 2.16 x 5.25 inches. This Ethernet/IP adapter module has an RJ-45, Category 5 Ethernet Connector. The Allen-Bradley 1734-AENT adapter acts as a bridge between the POINT I/O module and the network, so the user control real-time I/O data. This module has messaging data support for configuration and programming information (these are also known as explicit messages). The 1734-AENT adapter uses a Common Industrial Protocol (CIP). CIP is the application layer protocol that is specified for Ethernet/IP or Ethernet Industrial Protocol and for the ControlNet network and DeviceNet. This is a message-based protocol that implements a relative path for sending messages from the device in a system to the consuming device. When you apply power to the POINT I/O system and create an I/O connection, transition the output to Idle State, apply the Idle State data before switching to RUN mode. This happens even when the controller makes the connection in RUN mode.
Alternative names
- 1734AENT
- 173A-AENT
- 173AAENT
- L734-AENT
- L734AENT
- L73A-AENT
- L73AAENT
Frequently asked questions
What kind of series point is needed for the 1734-AENT?
You must use series C POINT I/O modules with the 1734-AENT adapter.
Does the 1734-AENT need its own IP address?
Yes, the 1734-AENT needs its own IP address.
Which POINT I/O modules series can I use with 1734-AENT?
Only use Series C with 1734-AENT. Series A and Series B POINT I/O modules are not compatible with 1734-AENT.
Can this module be purchased with a warranty?
Yes, the 1734-AENT comes with an one-year warranty from PLC-HUB.COM
Where can I send the 1734-AENT to be repaired?
PLC-HUB.COM, Inc. offers a variety of repair services for the 1734-AENT.
What is the maximum number of POINT I/O modules does the 1734-AENT support?
The 1734-AENT supports installation of up to 63 POINT I/O modules.
Does the 1734-AENT support installation of expansion power supply?
Yes. Expansion power supply is supported by the 1734-AENT. This is needed to allow the communication adapter maximize the number of modules supported.
What are the supported topologies of the embedded Ethernet port of the 1734-AENT?
The 1734-AENT supports star and tree topologies.
Technical notes
The Allen-Bradley 1734-AENT is a POINT I/O Ethernet/IP Adapter Module. It has 24 Volts DC Input Voltage Rating and a Inrush Current of 6 A max for 10 ms with the following Dimensions: 30in x 2.16in x 5.25 in. This Ethernet/IP Adapter Module has an RJ-45, Category 5 Ethernet Connector.
Original Links in Rockwell Automation
https://www.rockwellautomation.com.cn/products/details.1734-AENT.html
Reviews
There are no reviews yet.